DIY-FB-38_Plascon-Woodcare

Plascon Woodcare

interiorpack standardcolours tintbases

We are proud to be stockists of Plascon Woodcare products.

Prepare and protect your wooden surfaces with Plascon WoodCare Exterior/Interior Varnish.

It is a premium quality water-based wood varnish designed to penetrate deep into wood for maximum protection.

It has built-in UV stabilisers and preservatives to protect against moisture and increase the lifespan of wooden materials.

  • Quick Drying
  • Low Odour
  • Water Repellant
How to use Plascon Woodcare Exterior Varnish:

Wood that has been maintained creates a “living” piece that shows it is well cared for. Maintenance on a regular basis makes the actual task easier and adds years onto the life span of wood.

Below are the steps you can follow to ensure your Plascon Woodcare Exterior project achieves the best results:

 

Uses

Ideal for use on most wooden surfaces such as garage doors, shutters, window frames, doors, garden furniture, skirting, and gates.

Surface preparation

All surfaces must be clean, dry and sound. Remove any oil, grease, mortar droppings etc.

New Wood

Sand in the direction of the grain, to a smooth finish with 150 grit paper. Remove dust with a damp cloth.

Previously varnished wood in good condition

Sand to a matt finish to create a bond or key between the old and new coat. Remove dust with a damp cloth.

 

Previously varnished wood in bad condition

Remove old varnish completely by deep sanding or by using RemovALL All Purpose Paint Remover (RRA220).

Rinse thoroughly with fresh water. Allow surface to dry. Sand to a smooth finish. Remove dust with a damp cloth.

 

Wood previously coated with wax sealer/oil-based wood varnish

Remove all evidence of residue by mechanically sanding or by using RemovALL All Purpose Paint Remover (RRA220). Rinse thoroughly with fresh water. Allow surface to dry.

Sand to smooth finish. Remove dust with a damp cloth.

Previously painted wood

Strip old paint by deep sanding or by using RemovALL All Purpose Paint Remover. Rinse thoroughly with fresh water. Allow surface to dry. Sand bare wood to a smooth finish. Remove dust with a damp cloth.

Discoloured or weathered wood

Remove discoloured or weathered layer by sanding with 100 grit paper. Rinse thoroughly with fresh water. Allow surface to dry. Sand bare wood to a smooth finish. Remove dust with a damp cloth.

Knots in wood

Apply Plascon WoodCare Knot Seal (PK2).

Application

  • Stir contents thoroughly with a flat paddle until homogeneous.
  • Sand in the direction of the grain, to a smooth finish.
  • Apply the first coat by brush.
  • Allow to dry 4 hours.
  • Sand lightly in the direction of the grain between coats with ne paper and remove dust.
  • Apply subsequent coats in the same manner.
  • Minimum 2 coat application to new and previously coated wood.

 

How to use Plascon Woodcare Interior Varnish:

Wood that has been maintained creates a “living” piece that shows it is well cared for. Maintenance on a regular basis makes the actual task easier and adds years onto the life span of wood.

Below are the steps you can follow to ensure your Plascon Woodcare Interior project achieves the best results:

Uses

Ideal for use on most wooden surfaces such as interior doors, furniture, cupboards, skirting, counters, paneling and general interior wood surfaces.

Surface preparation

All surfaces must be clean, dry and sound. Remove any oil, grease, mortar droppings etc.

New Wood

Sand in the direction of the grain, to a smooth finish with 150 grit paper. Remove dust with a damp cloth.

Previously varnished wood in good condition

Sand to a matt finish to create a bond or key between the old and new coat. Remove dust with a damp cloth.

Previously varnished wood in bad condition

Remove old varnish completely by deep sanding or by using RemovALL All Purpose Paint Remover (RRA220). Rinse thoroughly with fresh water. Allow surface to dry. Sand to a smooth finish. Remove dust with a damp cloth.

 

Wood previously coated with wax sealer/oil-based wood varnish

Remove all evidence of residue by mechanically sanding or by using RemovALL All Purpose Paint Remover (RRA220). Rinse thoroughly with fresh water. Allow surface to dry. Sand to smooth finish. Remove dust with a damp cloth.

 

Previously painted wood

Strip old paint by deep sanding or by using RemovALL All Purpose Paint Remover. Rinse thoroughly with fresh water. Allow surface to dry. Sand bare wood to a smooth finish. Remove dust with a damp cloth.

 

Discoloured or weathered wood

Remove discoloured or weathered layer by sanding with 100 grit paper. Rinse thoroughly with fresh water. Allow surface to dry. Sand bare wood to a smooth nish. Remove dust with a damp cloth.

 

Knots in wood

Apply Plascon WoodCare Knot Seal (PK2).

 Application

  • Stir contents thoroughly with a flat paddle until homogeneous.
  • Sand in the direction of the grain, to a smooth finish.
  • Apply the first coat by brush and allow to dry for 4 hours.
  • Sand lightly in the direction of the grain between coats and remove dust.
  • Apply subsequent coats in the same manner.
  • Minimum 2 coat application to new and previously coated wood.

 For additional information go instore to your nearest Shave Paints store.